EDGE BLENDING ON CURVED WALL HOW TO
EDGE BLENDING ON CURVED WALL PRO
EDGE BLENDING ON CURVED WALL PROFESSIONAL

Make sure your artwork is sitting on a raised platform above your table or work area. Pouring over the edges can leave you with a clean, cohesive look if done correctly.

EDGE BLENDING ON CURVED WALL PROFESSIONAL

РІС™В РїС‘РЏ Caution: If youРІР‚в„ўre unfamiliar with using a table saw or power sander, speak to a friend who is, or a professional at your local hardware store. Once you trim the edges, you can paint them any color or leave them exposed so that you see the finished edge of the wood. Try not to waste too much, but donРІР‚в„ўt worry about some spilling over since you will be cutting the edge off anyway.Р”Р„fter the resin is fully cured, 48-72 hours, secure it to a wooden support so that you can use a table saw to cut through your artwork and the wooden support.

Alternatively, you can raise your artwork and not worry if some of the resin spills over. You can tape the edges so that the resin doesnРІР‚в„ўt pour over (see the description under #1 Create a Tape Dam). You have two different options to set up this type of edge. A table saw will cut cleanly through the resin, your artwork, and the wooden support. If you're using wood instead of canvas for your artwork, trimming the edges with a table saw will give it a clean, professional look.

EDGE BLENDING ON CURVED WALL PRO

СЂСџР‹РЃ Pro Tip: Painting the edges black will give your artwork a finished look. Once each side is smooth, you may paint them the color of your choosing. Sanding resin art takes more effort, but it will yield a smooth, clean edge.Р”Р„fter letting the resin run down the sides of your artwork, and letting it cure for 24 hours at the bare minimum, use sandpaper (80-200 grit) or a power sander to smooth out the edges of your artwork. Sandpaper (80-200 grit for shaping) OR power sander.Art 'N GlowРІР‚в„ўs Clear Casting and Coating Epoxy Resin will dome due to its higher viscosity level of 2600 cps. СЂСџР‹РЃ Pro Tip: Self-leveling resins are not ideal for doming, but it is still possible with viscous products. The resin will form a dome near all of the edges if you are precise as you spread it. It is best to push to one edge at a time. Gently brush the resin to the edges of your artwork being very careful that it does not drip over the edge. Pour your resin onto the center of your piece. (Use a level to make sure.) Otherwise, your resin will slip over the side of your piece and end up on the floor.

A thin resin can easily drip over the sides of your artwork.Р”В«efore pouring your resin, ensure the surface is completely level. To dome your epoxy resin, you will need to make sure the resin you are using is thick, as resins that have a higher surface tension, or higher viscosity values, are ideal for doming. You want the resin to be set, but still flexible so that the tape pulls off easily.Р”Вoming the edges of your project doesnРІР‚в„ўt require extra materials, but it does take some patience. Check on your resin to see if you can pull the tape off sooner. For the least hassle, it is best to remove the tape no more than 24 hours after pouring. If the resin completely hardens, it will be difficult to remove.

СЂСџР‹РЃ Pro Tip: One continuous piece of tape may be difficult to achieve, but aim for as few seams as possible.Р”ВonРІР‚в„ўt wait too long before removing the tape. The tape should stick up at least a half-inch. Press the tape around the entire project. If you want a thick layer of resin on a project, create a barrier (dam) around the edges with strong, durable tape, such as duct table or painters tape. In this post, weРІР‚в„ўll dig into each of the ways you can finish the edges of epoxy resin artwork. There are many options for finishing the edges of resin-coated artwork that will leave you with a unique final product. Whether youРІР‚в„ўre new to epoxy resin, need a refresher, or have years of experience, youРІР‚в„ўll find detailed instructions, including artist tips and safety advice.

EDGE BLENDING ON CURVED WALL HOW TO

СЂСџвЂ™РЋ Read our Step by Step Guide: How to Coat Paintings With Epoxy Resin. ItРІР‚в„ўs just a matter of deciding which one works best for you! Each technique will result in a different look. ItРІР‚в„ўs important to remember there are no wrong answers. You will want to decide this ahead of time since it will change the steps you follow, the tools you need, and the amount of resin you pour. Before you begin coating your artwork with epoxy resin, you need to decide how you are going to finish your epoxy resin edges.

Edge blending on curved wall